Holistic Self-Defense

  A Better Health Plan

  Chi Kung

  Depression and Anxiety

  Food and Energy

     "Dangers of Soy" Myth

     "Drink Water" Myth

     "Enzyme Heat" Myth

  Frequency Techniques

     ABPA Review

     F100 Series Review

     F-SCAN Review

     GB-4000 Review

     Rife Handbook Review

     Spooky2 Review

  Hadoscan and EAV


  Prevent or Cure Covid-19

     with Herbs

  Helpful Sites



  A Holistic Approach

  Beware the FDA!

     The FDA's Panacea

     Thirteen Years

     The Forbidden Fruit

     Aloe Irritates the FDA

     Institutional Torture

     The FDA's Cozy Little








  Effects (Eastern View)

  Effects (Western View)

  The FCC Standard

  Radiation Links


Seven Herbalists Speak

  Elisa Adams

  Diane Brigida

  Bill Fage

  Gene Fitzpatrick

  Cheryl Kelly

  Jeanne Polcari

  Joan Reardon


  Muscle Testing



Spooky2: Effective and Affordable

spooky.jpg (179218 bytes)Spooky2 is a new entry in the frequency generator field, a compact device powered by sophisticated software that invites favorable comparison with the Atelier Robin F100 series. 

There are some differences. It's a lot less expensive than most other such devices about 10% of the cost of an F165. Also, it can't be run standalone it requires the (free) Spooky2 software, downloadable from the Spooky website.

The generator transmits via contact mode (handgrips or pads), a plasma tube, or remotely, using small remote transmitters available as accessories. Einstein referred to remote transmission as "spooky action at a distance," from which the device's name is taken.

The generator has two output channels, but they aren't independent. The second one can be modified according to criteria you specify (adding and/or multiplying by a specific factor, changing the waveform, or performing other manipulations), but it can't run an entirely separate program. However, considering the low cost, if you wanted multiple independent channels, you could buy nine or ten Spookys for the cost of an F165 and run them all via the software (which can drive up to 127 of them). 

When driving multiple generators, however, you can't run more than one frequency derived from a main frequency for example, using Jeff Sutherland's programs and running two simultaneous scalar backfrequencies. You could run one on each of two generators, but you'd have to run the same main program on each one, and getting a double dose may not be advisable (in fact, the software has a setting to skip concurrent duplicate frequencies).

Another alternative, if all the frequencies have the same dwell time, is to put the first frequency at the end of the program on one device, so that machine A starts with the first frequency and its derivative and machine B starts with the second frequency and its derivative. At the end of the dwell time say, 3 minutes machine A moves on to the second frequency and machine B to the third one. So machine A would repeat each frequency with its own derivative immediately after machine B was done. Whether this would be equivalent to running them simultaneously is unclear.


The software uses "arbitrary waveforms" to create nine different types of waves instead of just the square and/or sine waves typically found on other machines. Some of them are reportedly more effective than square waves, but it would require systematic experimentation to determine this. The generator is available in three versions, with maximum frequencies of 5, 10, or 20MHz, at progressively higher prices. However because Spooky uses the software rather than the hardware to produce waveforms, the lowest- frequency, least-expensive generator (5MHz) is sufficient for all rifing purposes, according to the designer.

spooky_main_screen.jpg (164036 bytes)

The main software screen

The distinguishing feature of this software is that instead of having to write small programs, as with the F100 software, you just click buttons or fill fields to implement various functions. It may, in fact, have more functionality than the F100 software, but how useful this is is another question. It can seem a little daunting initially, since it has options for dozens of functions you'll probably never use because it's hard to tell what effect they have, if any.

Spooky offers over 6,400 built-in programs from various lists, but the best way to obtain frequencies (as I indicate at the end of the Rife Handbook review) is to dowse or muscle-test for them and create your own programs. However, in the Spooky software, creating a new program (or revising an existing one) is more cumbersome than it needs to be.

spooky_channel_screen.jpg (257739 bytes)
A screen for an individual channel

One problem is that Spooky doesn't automatically save programs with all the settings you've specified. You can save some of the settings, but not all of them, through a clumsy manual process. This means that when you reopen a program, you may have to redo some settings. If you're using a lot of non-default settings, this could be inconvenient.

Another issue is that the only way to move a program from the main list to the run list is to double-click it. If you're selecting a lot of programs, this is a prescription for carpal tunnel. It would be useful to be able to add a program to the run list by selecting it in the main list and hitting Enter.

spooky_advanced_screen.jpg (293205 bytes)
The Advanced screen, for controlling 
multiple generators and other functions

A final issue is that programs in the main list have a name (reflecting the malady they're intended for) followed by frequencies. When you transfer a program to the run list, it shows only the name. And when you actually run it, from another screen, it shows only the frequencies. It would be preferable to be able to see, on each screen, the frequencies and the program(s) they belong to.

These aren't major drawbacks, but they are noticeable. Hopefully a future update will remedy them.


A small, inexpensive remote unit is available that transmits frequencies via scalar waves using a fingernail clipping, eliminating the need to be near the generator during treatment. The photo at the beginning of this review shows two remotes connected to a Spooky2, using adapters (available separately) to eliminate the need for the supplied cables.

Another accessory, the Pulse, scans the body to provide a reading similar to the DIRP on an F-SCAN. I have reservations about the usefulness of the DIRP (see the F-SCAN review), and I found the Pulse even less effective. It shares the same disadvantages as the DIRP and seemed to take longer and be less convenient to use.

spooky_pulse.jpg (112071 bytes)
Spooky2 Pulse

Despite the comparatively minor disadvantages described above, the versatility and low cost of the Spooky2 make it a worthy competitor in the rife field and an effective way to try rifing without spending a lot of money.